5.1 Surround - COM 118 - Revision history

Wrrt7350: /* 118 Surround Sound 5.1 Setup */

2026-03-13T18:21:03Z

‎118 Surround Sound 5.1 Setup

Krusea at 01:15, 19 February 2026

2026-02-19T01:15:56Z

Vergaraz at 17:06, 22 April 2015

2015-04-22T17:06:32Z

Vergaraz at 17:06, 22 April 2015

2015-04-22T17:06:09Z

Vergaraz at 17:05, 22 April 2015

2015-04-22T17:05:49Z

Vergaraz: Created page with "118 Surround Sound 5.1 Setup -Check bundles for correct 5.1 channel placement Speakers - L R C LFE LS RS Apollo Outs - 33 34 35 36 37 38 -Assign..."

2015-04-22T16:57:55Z

Created page with "118 Surround Sound 5.1 Setup -Check bundles for correct 5.1 channel placement Speakers - L R C LFE LS RS Apollo Outs - 33 34 35 36 37 38 -Assign..."

New page

118 Surround Sound 5.1 Setup

-Check bundles for correct 5.1 channel placement
Speakers - L R C LFE LS RS
Apollo Outs - 33 34 35 36 37 38
-Assign outputs of tracks and master to 5.1 output

-PATCH:
-NEVE GROUP OUTPUTS (1-6) N17-22 →
118 SPL VOL. CTRL. INPUTS (L,R,C,LFE,LS,RS)V19-24
-118 SPL VOL. CNTRL OUTPUTS (L, R) U25,26→
118 C/R SPEAKER INPUTS (L,R) V 26,26

-On the Neve, assign channels 17-22 to groups 1-6 in corresponding order. (ie 17 -> 1, 18 -> 2, etc.). These will be your 6 surround output channels.
*Make sure ‘tape’ button is pressed in on these channels!!

-Make sure all buttons are pushed in on the 5. on the SPL Surround Monitor Controller. Also make sure all other buttons are not pushed in.
*This controller will be your main Volume
Control!!

-Bring up your levels in your project, the faders on ch. 17-22, and faders on groups 1-6.

[[Category:COM 118]]

@@ Line 1: / Line 1: @@
 == '''118 Surround Sound 5.1 Setup''' ==
-*Check bundles for correct 5.1 channel placement:
+*Check Pro Tools' bundles for correct 5.1 channel placement:
-**Speakers -       L     R    C   LFE   LS   RS 	Apollo Outs - 33  34  35   36    37   38
+**Speakers -       L     R    C   LFE   LS   RS  should be assigned to Apollo Outs - 17  18  19   20    21   22
 *Assign outputs of tracks and master to 5.1 output
 *'''PATCH:'''
-**NEVE GROUP OUTPUTS (1-6) N17-22  →  118 SPL VOL. CTRL. INPUTS (L,R,C,LFE,LS,RS)V19-24
+**NEVE GROUP OUTPUTS (1-6) (located at patch points) N17-22) to 118 SPL VOL. CTRL. INPUTS (L,R,C,LFE,LS,RS) (located at patch points V19-24)
-**-18 SPL VOL. CNTRL OUTPUTS (L, R) U25,26→ 	118 C/R SPEAKER INPUTS (L,R)   V 26,26
+**SPL VOL. CNTRL OUTPUTS (L, R) (located at patch points U25,26) must be patched to118 C/R SPEAKER INPUTS (L,R) (located at patch points V 25, 26)
-*On the Neve, assign channels 17-22 to groups 1-6 in corresponding order. (ie 17 -> 1, 18 -> 2, etc.).
+*On the Neve, assign channels 17-22 to groups 1-6 in corresponding order. (ie Channel 17 to Group 1, Channel 18 to Gropu 2, etc)
 **These will be your 6 surround output channels.
-*Make sure ‘tape’ button is pressed in on these channels!!
+*Make sure ‘tape’ button is pressed in on these channels
-*Make sure all buttons are pushed in on the 5. on the SPL Surround Monitor Controller.
+*Make sure all buttons that turn each 5.1 speaker on or off on the SPL Surround Monitor Controller are turned on.
 *Also make sure all other buttons are not pushed in.
 **This controller will be your main Volume Control!!
-*Bring up your levels in your project, the faders on ch. 17-22, and faders on groups 1-6.
+*Bring up your levels in your project, the faders on Channels 17 through 22, and faders on Groiups 1 through 6.
 [[Category:COM 118]]

@@ Line 1: / Line 1: @@
-'''118 Surround Sound 5.1 Setup'''
+== '''118 Surround Sound 5.1 Setup''' ==
 *Assign outputs of tracks and master to 5.1 output
 *'''PATCH:'''
--NEVE GROUP OUTPUTS (1-6) N17-22  →
+**NEVE GROUP OUTPUTS (1-6) N17-22  →  118 SPL VOL. CTRL. INPUTS (L,R,C,LFE,LS,RS)V19-24
-SPL VOL. CTRL. INPUTS (L,R,C,LFE,LS,RS)V19-24
+**-18 SPL VOL. CNTRL OUTPUTS (L, R) U25,26→ 	118 C/R SPEAKER INPUTS (L,R)   V 26,26
--118 SPL VOL. CNTRL OUTPUTS (L, R) U25,26→
 C/R SPEAKER INPUTS (L,R)   V 26,26
-*On the Neve, assign channels 17-22 to groups 1-6 in corresponding order. (ie 17 -> 1, 18 -> 2, etc.). These will be your 6 surround output channels.
+*On the Neve, assign channels 17-22 to groups 1-6 in corresponding order. (ie 17 -> 1, 18 -> 2, etc.).
 *Make sure ‘tape’ button is pressed in on these channels!!
-*Make sure all buttons are pushed in on the 5. on the SPL Surround Monitor Controller.   Also make sure all other buttons are not pushed in.
+*Make sure all buttons are pushed in on the 5. on the SPL Surround Monitor Controller.
-		*This controller will be your main Volume
+*Also make sure all other buttons are not pushed in.
-		   Control!!
+**This controller will be your main Volume Control!!
 *Bring up your levels in your project, the faders on ch. 17-22, and faders on groups 1-6.
 [[Category:COM 118]]

@@ Line 6: / Line 6: @@
 *Assign outputs of tracks and master to 5.1 output
-*PATCH:
+*'''PATCH:'''
 -NEVE GROUP OUTPUTS (1-6) N17-22  →
 SPL VOL. CTRL. INPUTS (L,R,C,LFE,LS,RS)V19-24

← Older revision		Revision as of 17:06, 22 April 2015
Line 1:		Line 1:
−	118 Surround Sound 5.1 Setup	+	'''118 Surround Sound 5.1 Setup'''

	*Check bundles for correct 5.1 channel placement		*Check bundles for correct 5.1 channel placement