Dual System Sound - Digital Video - Revision history

Williaas: /* Canon DSLR */

2018-11-19T22:06:11Z

‎Canon DSLR

2013-11-08T16:26:31Z

‎Canon DSLR

2012-02-08T21:50:04Z

2012-02-08T19:30:11Z

‎Slating

2012-02-08T19:29:01Z

2012-02-08T18:12:51Z

‎Camera Setup

2012-02-08T18:07:46Z

‎Slating

2012-02-08T01:32:19Z

2012-02-08T01:31:56Z

‎Slating

2012-02-08T01:09:34Z

@@ Line 4: / Line 4: @@
 ====Canon DSLR====
 * Use only the T2i model camera or higher for shooting with the 1920x1080 30 fps setting.
 * It is recommended to record a "scratch" audio track as a backup.
 * The camera audio is sometimes 1-2 frames out of sync from the video.
@@ Line 27: / Line 26: @@
 #After the Director calls "cut" both the sound engineer and camera operator should let the recording continue.
 #The AC should complete the slate calls in the reverse order and hold the clapper upside down to signify this is a tail slate.
   [[category:DSLR Video]]

@@ Line 3: / Line 3: @@
 ====Canon DSLR====
-* Use only the T2i model camera for shooting with the 1920x1080 30 fps setting.
+* Use only the T2i model camera or higher for shooting with the 1920x1080 30 fps setting.
 * The 1280 x 720 setting records at 60 fps which does not work with the '''Merge Clips''' function of '''Final Cut Pro'''.
-* It is recommended to record a "scratch" audio track on the T2i as a backup.
+* It is recommended to record a "scratch" audio track as a backup.
 * The camera audio is sometimes 1-2 frames out of sync from the video.

@@ Line 15: / Line 15: @@
 * There needs to be an audio and visual sync point at the beginning or end of each clip.
 * Use a clapperboard or clap your hands.
-* On the clapperboard write the production name, scene and take.
+* On the clapperboard write the production name, scene, shot, and take.
 ====Head Slate====

@@ Line 17: / Line 17: @@
 * On the clapperboard write the production name, scene and take.
-====Slating Procedures====
+====Head Slate====
 #Director or AD calls for "quiet on the set" and then for "roll sound".
 #The sound engineer will start recording and allow a few seconds of pre-roll before calling out "speed".
 #The camera operator will commence recording and call out "speed".
 #The AC will be holding the slate that is clearly labeled with scene information in front of the camera and the clapper sticks open. The AC will verbally state the slate information and call "marker" and close the sticks while holding this pose for a few seconds.
-*If a slate is not possible at the start of the take it can happen at the end
 #After the Director calls "cut" both the sound engineer and camera operator should let the recording continue.
 #The AC should complete the slate calls in the reverse order and hold the clapper upside down to signify this is a tail slate.

@@ Line 1: / Line 1: @@
 ===Camera Setup===
 * Format the memory card before recording.
 * Use only the T2i model camera for shooting with the 1920x1080 30 fps setting.
 * The 1280 x 720 setting records at 60 fps which does not work with the '''Merge Clips''' function of '''Final Cut Pro'''.

← Older revision	Revision as of 21:50, 8 February 2012
(No difference)

← Older revision		Revision as of 01:31, 8 February 2012
Line 14:		Line 14:
	* Use a clapperboard or clap your hands.		* Use a clapperboard or clap your hands.
	* On the clapperboard write the production name, scene and take.		* On the clapperboard write the production name, scene and take.
−	*	+
		+	===Slating Procedures===
		+	#Director or AD calls for "quiet on the set" and then for "roll sound".
		+	#The sound engineer will start recording and allow a few seconds of pre-roll before calling out "speed".
		+	#The camera operator will commence recording and call out "speed".
		+	#The AC will be holding the slate that is clearly labeled with scene information in front of the camera and the clapper sticks open. The AC will verbally state the slate information and call "marker" and close the sticks while holding this pose for a few seconds.
		+	*If a slate is not possible at the start of the take it can happen at the end
		+	#After the Director calls "cut" both the sound engineer and camera operator should let the recording continue.
		+	#The AC should complete the slate calls in the reverse order and hold the clapper upside down to signify this is a tail slate.
		+

	[[category:DSLR Video]]		[[category:DSLR Video]]

@@ Line 10: / Line 10: @@
 * 24 bits is recommended.
+===Slating===
 * There needs to be an audio and visual sync point at the beginning and /or end of each clip.
-** Use a clapperboard or clap your hands.
+* Use a clapperboard or clap your hands.
   [[category:DSLR Video]]