Film Editing Procedures - Revision history

Krusea: /* Set up the Rewinds and Viewer */

2026-02-12T18:56:16Z

‎Set up the Rewinds and Viewer

Krusea at 01:00, 12 February 2026

2026-02-12T01:00:27Z

Krusea at 21:46, 1 November 2017

2017-11-01T21:46:17Z

Krusea: /* Assembly Cut */

2017-10-31T17:47:41Z

‎Assembly Cut

Krusea: /* Assembly Cut */

2017-10-31T17:45:03Z

‎Assembly Cut

Krusea: /* Assembly Cut */

2017-10-31T17:40:37Z

‎Assembly Cut

Krusea: /* Watch your film */

2017-10-31T17:19:33Z

‎Watch your film

Krusea: /* Assembly Cut */

2017-10-31T17:11:24Z

‎Assembly Cut

Krusea: /* Assembly Cut */

2017-10-31T17:04:03Z

‎Assembly Cut

Krusea at 17:01, 31 October 2017

2017-10-31T17:01:19Z

@@ Line 9: / Line 9: @@
 == Set up the Rewinds and Viewer ==
 <gallery>
-Moviscop_Diagram.jpg
+Moviscop_Diagram.jpg |Moviscop Viewer |alt= Drawing of a Moviscop 16mm Viewer and threading diagram
 </gallery>
 # The reels, daylight spool and spring clamps have a notch in them.

@@ Line 1: / Line 1: @@
-==== Watch the film ====
+== Watch the film ==
 You will want to project the film to log the footage and take notes.
 # Project your rushes (The original film out of the camera).  You may need to do this more than once.
@@ Line 7: / Line 7: @@
 ## Whether you need to revise your script.
-==== Set up the Rewinds and Viewer ====
+== Set up the Rewinds and Viewer ==
 <gallery>
 Moviscop_Diagram.jpg
@@ Line 19: / Line 19: @@
 # Thread the film into the viewer.
-==== Find the Shots ====
+== Find the Shots ==
 Next you will want to find and cut out all of the shots you might want to use.
 # With the viewer identify the beginning and ending frames of each shot.
@@ Line 28: / Line 28: @@
 # Label each spool and set aside.
-==== Rough Cut ====
+== Rough Cut ==
 Now you can start editing the shots together.
-===== Head Leader =====
+=== Head Leader ===
 # Start with 4-5ft of leader.
 # It should be labeled with your name and the word "Head".
 # Wind this onto the the take up reel on the right side of the bench.
-===== Start Editing =====
+=== Start Editing ===
 # Start splicing the shots in order.
 # Only splice one side of the film.
-===== Tail Leader =====
+=== Tail Leader ===
 # At the end add 4-5ft of leader.
 # It should be labeled with your name and the word "Tail".
-===== Keep Editing =====
+=== Keep Editing ===
 # Watch the film on the viewer.
 # Fine tune edits and move shots around as desired.
 # Make sure to label any film you edit out in case you need it later.
-==== Fine Cut ====
+=== Fine Cut ===
 Prepare the film for projection.
 # Before the film can be projected it needs to be backspliced.
@@ Line 57: / Line 57: @@
 # Project the film.
-==== Re-edit ====
+=== Re-edit ===
 # If you need to make changes set up there film on the edit bench.
 # Carefully peel off the splice tape.

@@ Line 6: / Line 6: @@
 ## Whether it matches your original conception.
 ## Whether you need to revise your script.
 ==== Find the Shots ====
 Next you will want to find and cut out all of the shots you might want to use.
 # With the viewer identify the beginning and ending frames of each shot.
 # Mark the frames with grease pencil.

@@ Line 18: / Line 18: @@
 # Label each spool and set aside.
-==== Assembly Cut ====
+==== Rough Cut ====
 ===== Head Leader =====
@@ Line 39: / Line 40: @@
 ==== Fine Cut ====
 # Before the film can be projected it needs to be backspliced.
 # All cuts need to have splices on both sides.
 # Make sure alls pocket holes are clear.
 # Project the film.

@@ Line 1: / Line 1: @@
 ==== Watch the film ====
 # Project your rushes (The original film out of the camera).  You may need to do this more than once.
 # Discus what you shot:
@@ Line 7: / Line 8: @@
 ==== Find the Shots ====
 # Set up your rolls, in order on the editing bench.
 # Set up the film on the left side and wind onto the right side.