Difference between revisions of "Canon Rebel T1i/T2i Operating Guide"
| Line 17: | Line 17: | ||
The Canon Rebel shows charge level in three stages: Battery OK, Battery Low, and Needs to be Charged. To conserve battery life, the Rebel will go into a sleep mode after a period of disuse. To wake the camera, press the shutter button down halfway. If you know you will not be using the camera, it is best to fully turn the camera off. | The Canon Rebel shows charge level in three stages: Battery OK, Battery Low, and Needs to be Charged. To conserve battery life, the Rebel will go into a sleep mode after a period of disuse. To wake the camera, press the shutter button down halfway. If you know you will not be using the camera, it is best to fully turn the camera off. | ||
| + | ==Canon Rebel Lenses== | ||
| + | The Canon Rebel will accept any Canon EF of EF-S bayonet lenses. Media Loan has several different zoom and prime lenses that can be checked out alongside a Canon Rebel. | ||
| + | ===Removing and Replacing Lenses=== | ||
| + | Please do not remove the included kit lens from the camera unless you intend to attach a different lens immediately. | ||
| + | |||
| + | On the Canon Rebel, there is a half-circle shaped button on the right side of the lens mount (viewed from the front of the camera). To remove the lens, press this button, and turn the lens approximately 90 degrees clockwise. To attach a new lens, find the guide mark on the lens body. If it is an EF lens, the guide mark will be a red circle. If the lens is EF-S, the guide mark will be a white square. Line up the guide mark with the matching mark on the Canon rebel body, set the lens into the mount, and turn it approximately 90 degrees counter clockwise until it locks into place. | ||
Revision as of 14:39, 21 March 2013
Contents
Caring for the Canon Rebel
Media Loan has a limited number of Canon Rebel T1i/T2i cameras. We appreciate your help in caring for this item to insure it's long-term use at Evergreen.
General Camera Care DO NOT:
Drop this camera
Point camera toward Sun.
Submerge this camera in water
Leave this camera near a strong magnetic field!
Leave this camera in excessive heat, such as a car
Store this camera in excessive heat or cold
Use a blow dryer to blow dust from the camera
Store this camera in a location where there may be corrosive chemicals
Use excessive physical force
Please be gentle with this camera; it looks hardy, but it's delicate!
Battery
To insert a battery into the Canon rebel, open the battery door found on the bottom of the camera by pulling on the latch and swinging the door open. The battery will slide into place and lock in. Close the battery door. The battery will only fit in one way, so if it does not seem to be working, the battery is not oriented correctly.
To charge the battery, slide it into the provided charger and then plug the charger into a standard 120 VAC outlet. DO NOT CHARGE MORE THAN 24 HRS. DO NOT USE ANY CHARGER OTHER THAN THE ONE PROVIDED WITH THE CAMERA.
When the camera is powered off, it takes several seconds to clean the sensor. Because of this, make sure that the "Sensor Cleaning" logo is no longer on the screen before removing the battery.
Battery Life
The Canon Rebel shows charge level in three stages: Battery OK, Battery Low, and Needs to be Charged. To conserve battery life, the Rebel will go into a sleep mode after a period of disuse. To wake the camera, press the shutter button down halfway. If you know you will not be using the camera, it is best to fully turn the camera off.
Canon Rebel Lenses
The Canon Rebel will accept any Canon EF of EF-S bayonet lenses. Media Loan has several different zoom and prime lenses that can be checked out alongside a Canon Rebel.
Removing and Replacing Lenses
Please do not remove the included kit lens from the camera unless you intend to attach a different lens immediately.
On the Canon Rebel, there is a half-circle shaped button on the right side of the lens mount (viewed from the front of the camera). To remove the lens, press this button, and turn the lens approximately 90 degrees clockwise. To attach a new lens, find the guide mark on the lens body. If it is an EF lens, the guide mark will be a red circle. If the lens is EF-S, the guide mark will be a white square. Line up the guide mark with the matching mark on the Canon rebel body, set the lens into the mount, and turn it approximately 90 degrees counter clockwise until it locks into place.
