Difference between revisions of "APS Gimbal Operating Guide"

From Help Wiki
(6-POINT CALIBRATION)
 
(23 intermediate revisions by 6 users not shown)
Line 1: Line 1:
This is a restricted piece of equipment for advanced video students only. Students must be in an approved program for access to this equipment. The gimbal also requires a proficiency.
+
This is a restricted piece of equipment for advanced video students only. Students must be in an approved program for access to this equipment. [[APS Gimbal Proficiency Test|The gimbal also requires a proficiency.]]
 +
[[File:001 zpsxh3b9mth.jpg|none|thumb|562x562px]]
 +
 
 
==INTRO==
 
==INTRO==
Handheld 3-axis gimbals are used in stabilization systems designed to give the camera operator the independence of handheld shooting without camera vibration or shake. Powered by three brushless motors, the gimbals have the ability to keep the camera level on all axes as the camera operator moves the camera. An inertial measurement unit (IMU) responds to movement and utilizes its three separate motors to stabilize the camera. With the guidance of algorithms, the stabilizer is able to notice the difference between deliberate movement such as pans and tracking shots from unwanted shake. This allows the camera to seem as if it is floating through the air.  
+
Using Advanced Production Services equipment is a privilege
 +
and works differently than the rest of media loan. In order to request APS
 +
equipment, you must send in a work order 24 hours in advance to when you
 +
request the equipment. If you are not on time for pickup, the equipment you
 +
reserved may be given to someone else who requested it. Checkouts are for 2-3
 +
days and there are NO RENEWALS for APS equipment UNLESS you fill out an
 +
equipment renewal form 24 hours in advance. For more information about APS policy,
 +
visit: '''<nowiki>http://www.evergreen.edu/medialoan/aps-policies</nowiki>'''
 +
 
 +
Handheld
 +
3-axis gimbals are used in stabilization systems designed to give the camera
 +
operator the independence of handheld shooting without camera vibration or
 +
shake. Powered by three brushless motors, the gimbals have the ability to keep
 +
the camera level on all axes as the camera operator moves the camera. An
 +
inertial measurement unit (IMU) responds to movement and utilizes its three
 +
separate motors to stabilize the camera. With the guidance of algorithms, the
 +
stabilizer is able to notice the difference between deliberate movement such as
 +
pans and tracking shots from unwanted shake. This allows the camera to seem as
 +
if it is floating through the air.
 +
 
 +
The Advanced Production Services ''3-Axis Gimbal'' allows for steady camera movements in the x, y, and
 +
zed directions. The three
 +
axes to this gimbal are: Tilt Axis, The Roll Axis, and the Pan Axis.  
  
 
==CARE==
 
==CARE==
Line 28: Line 52:
 
*Use only the included charger
 
*Use only the included charger
 
*Do not overcharge (when fully charged, the indicator light will be solid green)
 
*Do not overcharge (when fully charged, the indicator light will be solid green)
 +
**  '''NEVER REMOVE BATTERY PACK FROM GIMBAL'''
  
 
==CONTENTS==
 
==CONTENTS==
*CAME-TV Argo Gimbal
+
*3-axis gimbal       
*Battery & Charger with cables
+
*gimbal stand        
*Stand
+
*One Lithium Polymer Battery Pack attached to gimbal ('''Stays on gimbal!''')        
*Remote
+
*One Lithium Polymer Fast Charge System        
*Tripod Adapter
+
*Gimbal remote and it’s charging station (USB)        
 +
*camera mount        
 +
*and camera mount adaptor[[File:Gimbal 4-01.jpg|thumb|544x544px|none]]
 +
### Gimbal Stand Handles
 +
### Mount for Gimbal remote
 +
### Handle Release - This will detach the gimbal from the handle. *'''DO NOT DO THIS'''*
 +
### Pan Axis Adjustment - Moves entire gimbal spine back and forward.
 +
### Lithium Polymer battery pack
 +
### Camera Mount (TAA) - Slides back to front (Release duck tail knob)
 +
### Roll Axis Adjustment - Moves from left to right, tightening screws located at back of gimbal.
 +
### Vertical Tilt Axis Adjustment - Brings the camera mount up or down.
  
 
==BASIC GIMBAL MECHANICS==
 
==BASIC GIMBAL MECHANICS==
 
[[file:Gimbal_3_axes_rotation.gif|right]]
 
[[file:Gimbal_3_axes_rotation.gif|right]]
The more you understand the mechanics of a gimbal, the easier it will be for you to use.
+
 
+
Before
===3-AXIS===
+
operating the gimbal, it is CRUCIAL to balance your camera on the gimbal in the
There are three axes to this gimbal: the yaw, pitch, and roll. Imagine three lines running through a camera mounted on the gimbal and intersecting at the camera's center of gravity. The gimbal moves and adjusts on these axes to create smooth camera operation.
+
three axes in order to achieve fluid movement with all 6 points. Imagine three
 
+
circles rotating interdependently of each other, where each circle rests inside
'''Yaw:''' Rotation around the vertical axis. You can think of yaw movement as pivoting, or turning, the position of the camera horizontally.<br />
+
the previous one. The first circle is the Tilt Axis which rotates vertically
'''Pitch:''' Rotation around the side-to-side axis. You can think of pitch movement as up-and-down vertical tilting.<br />
+
around the Center of Gravity. Inside that circle is the Roll Axis which spins
'''Roll:''' Rotation around the front-to-back axis.
+
horizontally from the Center of Gravity. Finally, the innermost circle is the Pan
 +
Axis, this rests on the vertical axis of the Roll, instead of from the Center
 +
of Gravity.
  
 
==BALANCING==
 
==BALANCING==
Line 52: Line 89:
 
Use the following steps, explained further below, to adjust the gimbal balance. '''DO NOT POWER ON THE BATTERY UNTIL AFTER BALANCING.'''
 
Use the following steps, explained further below, to adjust the gimbal balance. '''DO NOT POWER ON THE BATTERY UNTIL AFTER BALANCING.'''
  
===6-POINT CALIBRATION===
+
====MOUNTING THE CAMERA====
Prior to calibration, first set the gimbal up on the stand and mount the camera onto the gimbal. Then, follow the 6-point calibration steps listed below. <br />
+
[[File:Gimbal 3-02.jpg|none|thumb|197x197px]]
 +
#Attach the camera mounting plate to your camera using provided ¼” screw 
 +
#If using a follow focus or similar device, mount it on the camera before adding the camera to the gimbal body.
 +
#With the gimbal on the tuning stand facing outward, insert the camera until the safety lock is engaged. Make sure the gimbal is not turned on when balancing the camera.  
 +
#Tighten the camera base side clamp. You can adjust the tightness of the slide clamp with an M3 Allen wrench.
 +
[[File:Gimbal 4-03.jpg|none|thumb]]
  
You will know the gimbal is balanced if it reverts back to center and level after manipulation. Test the balance by gently tilting the pitch and roll and making the gimbal moves back into the level position. Yaw is the only point that does not revert back as it is a freely-moving axis until the gimbal is powered on.<br />
+
==== '''ADJUSTING HANDLE BARS''' ====
 +
The
 +
customizable handle bar on this gimbal can be adjusted for each individual
 +
user. Use the levers on the grips to loosen and then adjust the grips on the
 +
handle bar.
 +
[[File:GIMBAL 1-03.jpg|none|thumb|385x385px]]
  
'''Tip:''' Use a camera that has a programmed or built-in level, such as the Canon 6D from APS.<br />
+
'''The whole'''
 +
bar can be taken off when adjusting the grips. Leave the bar on this gimbal, it
 +
is there for the safety and protection of yourself and the equipment.
  
Manipulate the following adjustments to achieve proper balance:
+
====TILT AXIS ADJUSTMENT====
#Pitch axis horizontal (PAH)
+
This axis affects the forward and back tilting of the camera on the
#Pitch axis vertical (PAV)
+
gimbal. There are two calibrations which make up the Tilt Axis: 
#Row
+
#Rotation
+
#Roll axis
+
#Yaw axis
+
  
 +
#Begin with Tilt Axis Adjustment: The '''TAA''' is the orientation of the camera mount plate on the gimbal. As the name implies, the '''TAA''' affects the pitch (or up-down tilt) of the camera. You may need to move this forward or back, depending on the camera. It takes very small adjustments to balance the camera correctly. If properly balanced, the camera should be able to remain steady at any given tilt angle.
 +
[[File:Gimbal 4-03.jpg|none|thumb|426x426px]]
  
Each calibration adjustment affects the axes in different ways. We recommend that you follow this order, but you may find as you balance that you may need to re-adjust the different points as you go.  
+
'''Note:''' The best TAA position for the Canon 6D is the lowest.
  
====PITCH AXIS HORIZONTAL (PAH)====
+
====VERTICAL TILT ADJUSTMENT (VTA)====
The '''PAH''' is the orientation of the camera mount plate on the gimbal. As the name implies, the '''PAH''' affects the pitch (or up-down tilt) of the camera. You may need to move this forward or back, depending on the camera, if you wish to access the various input/outputs on the side of your camera. Do not mount the camera too far forward to too far back, try to find a position towards the center.
+
The '''VTA''' is the position height of
 +
the camera. As the name implies, the VTA affects the pitch (or up-down tilt) of
 +
the camera. You will need to move the camera higher or lower to level the
 +
camera and eliminate up-down tilt. To do this –
  
#Open the '''PAH lock catch'''.
+
#Rotate Tilt Axis so that the camera points skyward.    
#Move the camera forward or back to desired position
+
#Loosen the two ducktail knobs on the bottom of the gimbal arm and adjust the two knobs to raise and lower the camera.
#Close the lock catch to secure the position of the '''mount plate'''
+
#Once the camera remains skyward after release, the Vertical Tilt is correctly adjusted. Make sure that the measurements on each side are the same or the motor could jam.
 +
[[File:GIMBAL 1-02.jpg|none|thumb|298x298px]]
 +
[[File:Gimbal 4-02.jpg|none|thumb]]
 +
[[File:GIMBAL 1-01.jpg|none|thumb|299x299px]]
  
====PITCH AXIS VERTICAL (PAV)====
+
====ROLL AXIS====
The '''PAV''' is the position height of the camera. As the name implies, the PAV affects the pitch (or up-down tilt) of the camera. You will need to move the camera higher or lower to level the camera and eliminate up-down tilt.
+
This axis effects the rotational abilities of the
 +
gimbal, and allows for fluid rotational movement from the neck and arm of the
 +
gimbal. When the proper left/right roll balance is achieved, the camera will
 +
stay level. 
  
#Open the two '''PAV lock catches'''.
+
#Loosen the two lock-knobs at the bottom of the gimbal plate in order to make adjustments.  
#On both sides, use the '''PAV adjustment knobs''' to raise/lower the height of the camera. Set to a position in which the camera remains level.
+
#Slide the camera left and right until the Roll Axis remains level    
#Make sure both sides are in a matched position on their prospective '''PAV scales'''.
+
#Retighten the two lock-knobs which keep the Roll position.  
#Close the '''PAV lock catches'''.
+
[[File:GIMBAL ILL-03.jpg|none|thumb]]
 +
[[File:Gimbal 3-01.jpg|none|thumb]]
  
 +
====PAN AXIS ADJUSTMENT====
 +
The '''PAA'''
 +
is an adjustment of the gimbal’s '''spine''',
 +
the space between the handles and the gimbal arm. To achieve balance while
 +
panning:
 +
# Loosen the ducktail knob on the top of the gimbal spine.
 +
# Then, use the knob at the back of the gimbal above the battery pack to adjust the pan Axis. Check to see if the camera is either top heavy or bottom heavy and then turn the knob to adjust the forward and back position of the spine. While the gimbal is on the tuning stand, Rotate the gimbal along the pan axis by lifting one side of the handle bar. If the camera does not swing, the axis is properly balanced. Ensure the ducktail knob is tightened to keep the adjustment in place.
 +
[[File:GIMBAL ILL-01.jpg|none|thumb|335x335px]]
  
'''Note:''' The best PAV position for the Canon 6D is the lowest.
+
====ADVANCED ROLL ADJUSTMENTS====
 +
The '''ARA''' is
 +
used when additional adjustment is needed. This is typically when the camera
 +
body is too lightweight in comparison to the gimbal’s motor system. Use the
 +
Allan knobs to loosen the adjustment and then slide the whole arm left or right
 +
to compensate for the lightweight camera. 
  
====ROW====
+
==REMOTE OPERATION==
The row adjustment affects the roll axis and changes the horizontal positioning of the camera. Adjust the row to the left or right to eliminate side-to-side leaning of the camera.
+
Once the
 +
camera is stabilized by going through 6-point calibration, turn on the gimbal
 +
by pressing once, and then holding the button down a second time until the
 +
lights flashes and you hear a beep. The gimbal will engage and keep the camera
 +
balanced.
  
#Loosen the '''row lock knobs'''.
+
The remote
#Adjust the camera to the left or right until level. Let go of camera to test leaning.
+
for the gimbal allows you to control the movements of the three axes with a
#Tighten the '''row lock knobs'''.
+
thumb-pad. The remote is turned on the same way, press the button once and then
 +
hold the button down a second time to turn on.  
  
====ROTATION====
+
====TO TURN ON/OFF====  
Rotation refers to the forward-backward leaning of the entire gimbal body. The '''spine''' of the body should be straight up and down. This adjustment re-distributes the weight of the gimbal along the '''neck'''. If there is a dip in the front of the gimbal, this means that the front is heavier, and this adjustment needs to be moved back. If there is a rise in the front, move this forward.
+
Press and hold the '''power/mode button''' for 3 seconds, or until the indicator light turns on/off. A '''green light''' means the battery is charged and the signal is normal. A '''slowly-flashing red light''' means the battery is getting low, and a '''quickly-flashing red light''' means the remote needs to be charged immediately.
 +
[[File:Gimbal 3-03.jpg|thumb|359x359px|none]]
 +
1.   Directional thumb pad – Use to direct the direction the
 +
gimbal moves.
  
#Open the '''rotation lock catch'''.
+
2.   USB Charge port – Plug USB micro into wall adapter to charge
#Move the '''rotate knob''' forward or back until the spine is straight and there is no rise or dip in the front of the gimbal.
+
remote.  
#Close the '''rotation lock catch'''.
+
  
====ROLL====
+
3.   Status Button – Green – Aligning code/ Status nominal button. Red – Not communicating with Gimbal/battery life low.
Use the '''roll screw''' to change the roll adjustment if the camera is not able to roll freely. Do not over-tighten or over-loosen this screw.
+
  
====YAW====
+
4.   Power switch/Mode change button – Press once to turn on, then
The YAW can be set to any position prior to usage, but the standard set-up is for the '''neck''' to be perpendicular with the '''arm'''.
+
press again to sync with gimbal. Once on and synced, press the button the
 +
number of times corresponding with the desired mode (1-3).          
  
==REMOTE OPERATION==
+
Use the
The remote is necessary for operation of the gimbal. The three main functions of the remote are:
+
remote to make adjustments to tilt and pan, do not make those adjustments on
*Adjusting the desired set-up position of the gimbal
+
the gimbal itself, it may through the balance off.  
*Selecting the operation mode of the gimbal
+
*Performing camera movements (pan, tilt).
+
  
To operate the remote, use the power/mode button to turn the remote on/off as well as to select the desired operation mode of the gimbal. Use the joystick to control pitch and yaw of the gimbal for camera tilts and pans.
+
The remote
 +
does not have any visual indicator for which mode it is in. Instead it relies
 +
on communicating with the gimbal in order to indicate which mode it is in.
 +
Pressing the button once will put you into mode 1 and the gimbal will beep
 +
once. Two times and it will enter the second mode and beep 2 times. Finally, if
 +
you press the button 3 times, the gimbal enters mode 3 and beeps 3 times.  
  
====TO TURN ON/OFF====
+
There are
Press and the power/mode button for 3 seconds, or until the indicator light turn on/off. A '''green light''' means the battery is charged and the signal is normal. A '''slowly-flashing red light''' means the battery is getting low, and a '''quickly-flashing red light''' means the remote needs to be charged immediately.
+
three distinct remote settings:
  
====MODE SELECTION====
+
# '''(Press      Once - follow tilt, follow pan.)''' The gimbal will respond      and adjust to new tilt and pan positions as you move. This mode is ideal      for a versatile subject/shot that needs quick adaptation.
After the remote is on, you can use the power/mode button to set the operational mode for the gimbal. <br />
+
# '''(Press      Twice - lock tilt, follow pan.)''' The gimbal will remain at      the set tilt position, but you will be able to adjust the pan position as      you move. This mode is ideal for a tracking shot around a corner.
 +
# '''(Press      Thrice - lock tilt, lock pan.)''' The tilt and pan      positions will remain locked. This mode is ideal for linear tracking      shots.
 +
<br />Charge the remote with the included power adaptor and cable. The remote needs 1.5 hours to fully charge and typically lasts for 8 hours.
  
'''Before selecting a mode''' to use, set the gimbal in the desired position (after balancing!). The default position for most shooting situations is completely center and level. You may desire a different effect however, such as a slight tilt up/down. '''DO NOT CHANGE THE AXIS ADJUSTMENTS TO PLACE THE CAMERA IN AN ALTERNATE POSITION.''' Use only the remote to make these adjustments so as to not mess up the balance.<br />
+
==BATTERY OPERATION==
 +
1.   
 +
Check
 +
the power level -  Quickly press the
 +
power button once. The light will indicate the power level (1-4 bars). The
 +
charge will display on the 4 LEDS on the back, 4 bars is fully charged.
  
After positioning the gimbal, change the mode by pressing the power/mode button the following number of times:
+
2.   
# '''follow pitch, follow yaw.''' The gimbal will respond and adjust to new pitch and yaw positions as you move. This mode is ideal for a versatile subject/shot that needs quick adaptation.
+
To
# '''lock pitch, follow yaw.''' The gimbal will remain at the set pitch position, but you will will be able to adjust the yaw position as you move. This mode is ideal for a tracking shot around a corner.
+
Turn on – Quickly press the power button once, the indicator light will turn
# '''lock pitch, lock yaw.'''  The pitch and yaw positions will remain the locked. This mode is ideal for linear tracking shots.
+
on. Press and hold the power button again and the battery will turn on. You’ll
 +
know it’s on when the lights remain lit and the gimbal beeps.
  
====REMOTE CHARGING====
+
3.   
Charge the remote with the included power adaptor and cable. The remote needs 1.5 hours to fully charge and typically lasts for 8 hours.
+
To
 +
Turn off – Quickly press the power button once, the indicator light will flash.
 +
Press and hold the power button again until the lights turn off. You’ll know
 +
it’s off when you can freely move all three axes.  
  
==BATTERY OPERATION==
+
== Operation Modes ==
'''Check the power level:''' Quickly press the power button once. The light will indicate the power level.<br />
+
 
'''To turn on:''' Quickly press the power button once, the indicator light will turn on. Press and hold the power button again and the battery will turn on. You'll know it's on when the lights stay lit and the gimbal beeps.<br />
+
=== Underslung Method - ===
'''To turn off:''' Quickly press the power button once, the indicator light will flash. Press and hold the power button again until the lights turn off. You'll know it's off when you can freely move the axis.
+
1.   
 +
Underslung
 +
mode is the standard, default mode. It can be used without any user input.
 +
 
 +
=== Upright Method - ===
 +
# Flip the gimbal upwards 180 degrees to change to upright mode. Upright mode is ideal for high camera positions, as it allows you to shoot higher and/or at eye level. This mode can be used without any user input. 
 +
 
 +
=== Briefcase Method - ===
 +
# Briefcase mode allows you to hold the gimbal in a slim profile close to your body. To enter this mode, tilt the gimbal on the roll axis 90 degrees to the left or right.  
 +
 
 +
'''When you are finished using'''
 +
the gimbal, make sure to put away all equipment tidily, remove the battery pack
 +
from the gimbal.
  
 
==TROUBLESHOOTING==
 
==TROUBLESHOOTING==
You may experience some issues when attempting to operate the gimbal, such as vibration and drifting. The most common cause of gimbal misbehavior is improper balancing. If you're experiencing these difficulties, use the various axis adjustments to properly, and completely, re-balance the gimbal. If the gimbal continues to misbehave, or is having an issue with battery/motor power, please ask for help from APS by stopping in or calling x5506 during open hours.  
+
1.        
 +
'''The motor is weak''' ……………. Check to see if the voltage settings
 +
are nominal or not
 +
 
 +
2.        
 +
'''Vibrating and jittering'''………… Double check your balance/calibration of
 +
the axes, make sure all screws are locked and tightened.
 +
 
 +
3.        
 +
'''Roll Axis diverges at CoG'''…… Check if the CoG for the rotational axis
 +
is set correctly. Otherwise, redo the calibration.  
 +
 
 +
4.        
 +
'''Drifting'''……………………………The 6-point calibration is off or the gimbal
 +
is being interrupted by a different magnetic field.  
  
 +
5.        
 +
'''Motor shutdown''' ………………. Check to see if the battery has a
 +
charge left, it may have died.
  
[[Category:Media Loan]]
+
'''You may experience some issues attempting to'''
 +
operate this gimbal. The most common problems are caused by an improper
 +
balancing of the device. If the gimbal continues to misbehave, or is having
 +
technical issues that are not covered in this manual, bring the equipment back
 +
to APS or call x5506 during business hours to receive aid from Media Loan
 +
Staff.'''  '''
 +
[[Category:Media Loan Tests]]

Latest revision as of 13:32, 26 March 2021

This is a restricted piece of equipment for advanced video students only. Students must be in an approved program for access to this equipment. The gimbal also requires a proficiency.

001 zpsxh3b9mth.jpg

INTRO

Using Advanced Production Services equipment is a privilege and works differently than the rest of media loan. In order to request APS equipment, you must send in a work order 24 hours in advance to when you request the equipment. If you are not on time for pickup, the equipment you reserved may be given to someone else who requested it. Checkouts are for 2-3 days and there are NO RENEWALS for APS equipment UNLESS you fill out an equipment renewal form 24 hours in advance. For more information about APS policy, visit: http://www.evergreen.edu/medialoan/aps-policies

Handheld 3-axis gimbals are used in stabilization systems designed to give the camera operator the independence of handheld shooting without camera vibration or shake. Powered by three brushless motors, the gimbals have the ability to keep the camera level on all axes as the camera operator moves the camera. An inertial measurement unit (IMU) responds to movement and utilizes its three separate motors to stabilize the camera. With the guidance of algorithms, the stabilizer is able to notice the difference between deliberate movement such as pans and tracking shots from unwanted shake. This allows the camera to seem as if it is floating through the air.

The Advanced Production Services 3-Axis Gimbal allows for steady camera movements in the x, y, and zed directions. The three axes to this gimbal are: Tilt Axis, The Roll Axis, and the Pan Axis.

CARE

The gimbal at Media Loan is a complicated (and expensive!) piece of equipment that requires special attention and care. If not used and stored properly it can be permanently damaged. These potential damages may lead to accidents and hazards. Please use thorough care with this equipment.

ALWAYS:

  • Make sure all screws and locks are secured tightly before operation
  • Store in a cool, dry place
  • Only use handles to carry gimbal.
  • Use the stand to set-up the gimbal for use
  • Make sure that the roll and pitch axis cables do not become tangled
  • Properly balance the gimbal prior to operation


NEVER:

  • Expose to excessive heat, such as a furnace
  • Store any items in the case besides those included in the kit
  • Use excessive force with any of the parts
  • Use in a location with strong static electricity
  • Set the gimbal directly on a surface. You MUST use the stand.
  • Use in the rain or non-dry weather
  • Pick up the gimbal with any other part than the handles
  • Force the gimbal to move when locked

BATTERY

  • Only use the included battery with this equipment
  • Use only the included charger
  • Do not overcharge (when fully charged, the indicator light will be solid green)
    • NEVER REMOVE BATTERY PACK FROM GIMBAL

CONTENTS

  • 3-axis gimbal     
  • gimbal stand      
  • One Lithium Polymer Battery Pack attached to gimbal (Stays on gimbal!)      
  • One Lithium Polymer Fast Charge System      
  • Gimbal remote and it’s charging station (USB)      
  • camera mount      
  • and camera mount adaptor
    Gimbal 4-01.jpg
      1. Gimbal Stand Handles
      2. Mount for Gimbal remote
      3. Handle Release - This will detach the gimbal from the handle. *DO NOT DO THIS*
      4. Pan Axis Adjustment - Moves entire gimbal spine back and forward.
      5. Lithium Polymer battery pack
      6. Camera Mount (TAA) - Slides back to front (Release duck tail knob)
      7. Roll Axis Adjustment - Moves from left to right, tightening screws located at back of gimbal.
      8. Vertical Tilt Axis Adjustment - Brings the camera mount up or down.

BASIC GIMBAL MECHANICS

Gimbal 3 axes rotation.gif

Before operating the gimbal, it is CRUCIAL to balance your camera on the gimbal in the three axes in order to achieve fluid movement with all 6 points. Imagine three circles rotating interdependently of each other, where each circle rests inside the previous one. The first circle is the Tilt Axis which rotates vertically around the Center of Gravity. Inside that circle is the Roll Axis which spins horizontally from the Center of Gravity. Finally, the innermost circle is the Pan Axis, this rests on the vertical axis of the Roll, instead of from the Center of Gravity.

BALANCING

Prior to operation, the gimbal must be properly balanced. If it's not, the gimbal will not function properly. Balanced means that the gimbal and camera is centered and leveled, with no part tilting up/down or to the side.

Use the following steps, explained further below, to adjust the gimbal balance. DO NOT POWER ON THE BATTERY UNTIL AFTER BALANCING.

MOUNTING THE CAMERA

Gimbal 3-02.jpg
  1. Attach the camera mounting plate to your camera using provided ¼” screw 
  2. If using a follow focus or similar device, mount it on the camera before adding the camera to the gimbal body.
  3. With the gimbal on the tuning stand facing outward, insert the camera until the safety lock is engaged. Make sure the gimbal is not turned on when balancing the camera.
  4. Tighten the camera base side clamp. You can adjust the tightness of the slide clamp with an M3 Allen wrench.
Gimbal 4-03.jpg

ADJUSTING HANDLE BARS

The customizable handle bar on this gimbal can be adjusted for each individual user. Use the levers on the grips to loosen and then adjust the grips on the handle bar.

GIMBAL 1-03.jpg

The whole bar can be taken off when adjusting the grips. Leave the bar on this gimbal, it is there for the safety and protection of yourself and the equipment.

TILT AXIS ADJUSTMENT

This axis affects the forward and back tilting of the camera on the gimbal. There are two calibrations which make up the Tilt Axis: 

  1. Begin with Tilt Axis Adjustment: The TAA is the orientation of the camera mount plate on the gimbal. As the name implies, the TAA affects the pitch (or up-down tilt) of the camera. You may need to move this forward or back, depending on the camera. It takes very small adjustments to balance the camera correctly. If properly balanced, the camera should be able to remain steady at any given tilt angle.
Gimbal 4-03.jpg

Note: The best TAA position for the Canon 6D is the lowest.

VERTICAL TILT ADJUSTMENT (VTA)

The VTA is the position height of the camera. As the name implies, the VTA affects the pitch (or up-down tilt) of the camera. You will need to move the camera higher or lower to level the camera and eliminate up-down tilt. To do this –

  1. Rotate Tilt Axis so that the camera points skyward.    
  2. Loosen the two ducktail knobs on the bottom of the gimbal arm and adjust the two knobs to raise and lower the camera.
  3. Once the camera remains skyward after release, the Vertical Tilt is correctly adjusted. Make sure that the measurements on each side are the same or the motor could jam.
GIMBAL 1-02.jpg
Gimbal 4-02.jpg
GIMBAL 1-01.jpg

ROLL AXIS

This axis effects the rotational abilities of the gimbal, and allows for fluid rotational movement from the neck and arm of the gimbal. When the proper left/right roll balance is achieved, the camera will stay level. 

  1. Loosen the two lock-knobs at the bottom of the gimbal plate in order to make adjustments.
  2. Slide the camera left and right until the Roll Axis remains level    
  3. Retighten the two lock-knobs which keep the Roll position.
GIMBAL ILL-03.jpg
Gimbal 3-01.jpg

PAN AXIS ADJUSTMENT

The PAA is an adjustment of the gimbal’s spine, the space between the handles and the gimbal arm. To achieve balance while panning:

  1. Loosen the ducktail knob on the top of the gimbal spine.
  2. Then, use the knob at the back of the gimbal above the battery pack to adjust the pan Axis. Check to see if the camera is either top heavy or bottom heavy and then turn the knob to adjust the forward and back position of the spine. While the gimbal is on the tuning stand, Rotate the gimbal along the pan axis by lifting one side of the handle bar. If the camera does not swing, the axis is properly balanced. Ensure the ducktail knob is tightened to keep the adjustment in place.
GIMBAL ILL-01.jpg

ADVANCED ROLL ADJUSTMENTS

The ARA is used when additional adjustment is needed. This is typically when the camera body is too lightweight in comparison to the gimbal’s motor system. Use the Allan knobs to loosen the adjustment and then slide the whole arm left or right to compensate for the lightweight camera. 

REMOTE OPERATION

Once the camera is stabilized by going through 6-point calibration, turn on the gimbal by pressing once, and then holding the button down a second time until the lights flashes and you hear a beep. The gimbal will engage and keep the camera balanced.

The remote for the gimbal allows you to control the movements of the three axes with a thumb-pad. The remote is turned on the same way, press the button once and then hold the button down a second time to turn on.

TO TURN ON/OFF

Press and hold the power/mode button for 3 seconds, or until the indicator light turns on/off. A green light means the battery is charged and the signal is normal. A slowly-flashing red light means the battery is getting low, and a quickly-flashing red light means the remote needs to be charged immediately.

Gimbal 3-03.jpg

1.   Directional thumb pad – Use to direct the direction the gimbal moves.

2.   USB Charge port – Plug USB micro into wall adapter to charge remote.

3.   Status Button – Green – Aligning code/ Status nominal button. Red – Not communicating with Gimbal/battery life low.

4.   Power switch/Mode change button – Press once to turn on, then press again to sync with gimbal. Once on and synced, press the button the number of times corresponding with the desired mode (1-3).

Use the remote to make adjustments to tilt and pan, do not make those adjustments on the gimbal itself, it may through the balance off.

The remote does not have any visual indicator for which mode it is in. Instead it relies on communicating with the gimbal in order to indicate which mode it is in. Pressing the button once will put you into mode 1 and the gimbal will beep once. Two times and it will enter the second mode and beep 2 times. Finally, if you press the button 3 times, the gimbal enters mode 3 and beeps 3 times.

There are three distinct remote settings:

  1. (Press Once - follow tilt, follow pan.) The gimbal will respond and adjust to new tilt and pan positions as you move. This mode is ideal for a versatile subject/shot that needs quick adaptation.
  2. (Press Twice - lock tilt, follow pan.) The gimbal will remain at the set tilt position, but you will be able to adjust the pan position as you move. This mode is ideal for a tracking shot around a corner.
  3. (Press Thrice - lock tilt, lock pan.) The tilt and pan positions will remain locked. This mode is ideal for linear tracking shots.


Charge the remote with the included power adaptor and cable. The remote needs 1.5 hours to fully charge and typically lasts for 8 hours.

BATTERY OPERATION

1.    Check the power level -  Quickly press the power button once. The light will indicate the power level (1-4 bars). The charge will display on the 4 LEDS on the back, 4 bars is fully charged.

2.    To Turn on – Quickly press the power button once, the indicator light will turn on. Press and hold the power button again and the battery will turn on. You’ll know it’s on when the lights remain lit and the gimbal beeps.

3.    To Turn off – Quickly press the power button once, the indicator light will flash. Press and hold the power button again until the lights turn off. You’ll know it’s off when you can freely move all three axes.

Operation Modes

Underslung Method -

1.    Underslung mode is the standard, default mode. It can be used without any user input.

Upright Method -

  1. Flip the gimbal upwards 180 degrees to change to upright mode. Upright mode is ideal for high camera positions, as it allows you to shoot higher and/or at eye level. This mode can be used without any user input. 

Briefcase Method -

  1. Briefcase mode allows you to hold the gimbal in a slim profile close to your body. To enter this mode, tilt the gimbal on the roll axis 90 degrees to the left or right.

When you are finished using the gimbal, make sure to put away all equipment tidily, remove the battery pack from the gimbal.

TROUBLESHOOTING

1.         The motor is weak ……………. Check to see if the voltage settings are nominal or not

2.         Vibrating and jittering………… Double check your balance/calibration of the axes, make sure all screws are locked and tightened.

3.         Roll Axis diverges at CoG…… Check if the CoG for the rotational axis is set correctly. Otherwise, redo the calibration.

4.         Drifting……………………………The 6-point calibration is off or the gimbal is being interrupted by a different magnetic field.

5.         Motor shutdown ………………. Check to see if the battery has a charge left, it may have died.

You may experience some issues attempting to operate this gimbal. The most common problems are caused by an improper balancing of the device. If the gimbal continues to misbehave, or is having technical issues that are not covered in this manual, bring the equipment back to APS or call x5506 during business hours to receive aid from Media Loan Staff.