Waveform Editing - Audition

From Help Wiki
Revision as of 14:54, 20 October 2015 by Krusea (Talk | contribs) (Volume)

Waveform Editing

Waveform Editing is for editing single audio files- .mp3, .wav, .aiff, etc. It is a form of Destructive Editing. When changes are made to the waveform file they also permanently alter the original file. Waveform Editing is useful for a Fade In or Fade Out, Normalizing, simple Editing, and converting sound files from Stereo to Mono. Waveform Editing provides a visualization of the audio file's Sound Waves.

Open a File

  1. Choose the Waveform Mode at top left of the Audition Panel.
  2. Under the Audition Main Menu select File > Open File > and select your audio file. PKF files are visualizations of the sound waves. Do not import these files into Audition.
  3. The audio file should appear in the Files Window with its name and duration.
  4. The audio file can be dragged from the Files Window into the Waveform Timeline to begin editing.
    • If the audio file is a Stereo Recording the Left Track will be displayed on top of the Right Track.
    • Each track can be independently disabled by clicking either the L and R or 1 and 2 boxes corresponding to each track on the far right end of the timeline.

Normalize

Normalizing your audio file is the application of a constant amount of Gain to an audio recording to bring the average or Peak Amplitude to a target level.

To Normalize your audio file:

  1. Under the Audition Main Menu select Favorites > Normalize to -0.1dB or to Normalize to -3dB, depending on how much average peak amplitude change is necessary.

Editing

Removing unwanted sections of the audio file using Cut:

  1. Hold down the right cursor on the mouse in the Waveform Timeline, dragging it over the desired audio to delete from the selection.
  2. Once the desired clip is highlighted, go to the Audition Main Menu and select Edit > Cut. This will delete the highlighted selection.


Duplicating audio clips using Copy and Paste:

  1. Hold down the right cursor on the mouse in the Waveform Timeline, dragging it over the desired selection to duplicate.
  2. Once the desired clip is highlighted, go to the Audition Main Menu and select Edit > Copy.
  3. Place the Playhead at the desired location on the Waveform Timeline to Paste the copied clip.
  4. Once the desired Paste position is set, go to the Audition Main Menu and select Edit > Paste.


To isolate a Specific Clip from larger audio file for editing:

  1. Hold down the right cursor on the mouse, dragging it over the desired audio for the new clip.
  2. Once the desired clip is highlighted in the Waveform Timeline, go to the Audition Main Menu and select Edit > Copy to New
  3. The Waveform Timeline should now only display the specific clip.

Volume

Editing Volume or Amplitude can be competed in several ways:

To edit Volume of an audio file:

  1. Use the Amplify icon that appears on top of with clip. Before any changes are applied, the icon will read +0dB.
  2. By dragging the mouse over this icon, the amplitude can either be increased, by dragging to the right, or decreased, by dragging to the left.


OR

  1. Go to the Audition Main Menu and select Effects > Amplitude and Compression > Amplify.
  2. In the Effect - Amplify Window change the Amplitude Meter by dragging the mouse to either increase or decrease the dBs.
    • It is best to raise or lower a file's amplitude in small increments.
    • Do not increase amplitude where peaks are no longer visible on the screen. This will create Distortion.
  3. Once you have completed the desired change in amplitude select Apply to apply changes to entire file.

Fade In and Fade Out

To apply a Fade In and Fade Out go to the Audition Main Menu and select Favorites > Fade In and then reselect Favorites > Fade Out.

OR

At the top lefthand and righthand side of the Waveform Timeline there are gray boxes that allow for Linear Fades to be applied to the audio file. By holding down the right cursor on the mouse while hovering over the box, the mouse can be dragged to a desired Linear Fade Value to produce a Fade In and Fade Out.

Stereo to Mono

Converting Stereo to Mono takes the audio recording from two channels to one channel.

To convert from Stereo to Mono:

  1. Under the Audition Main Menu select Favorites > Convert to Mono

Save the File