Difference between revisions of "Headphone Mixes-COM 212"

From Help Wiki
(→‎Creating Headphone Mixes in COM 212)
m (→‎Headphone Mixes in COM 212A: edited to include pressing TB button to assign talkback to cues.)
 
(8 intermediate revisions by 4 users not shown)
Line 1: Line 1:
−
===Headphone Mixes in COM212===
+
__NOTOC__
 +
===Headphone Mixes in COM 212A===
  
−
There are '''Q''' 1 & 2 jacks in the 107 Recital Hall.
+
There are '''Q''' 1 & 2 jacks in the 107 Recital Hall. Plug each Little Red Cue Box into either Cue 1 or 2 with the included 1/4" to XLR speaker-level cable. This is the ONLY cable that should be used with the LRCB. Make sure the volume on the LRCB is turned all the way down when not in use.
  
 
===='''CUE 1'''====
 
===='''CUE 1'''====
−
#Cue 1 out of your DAW is normalized into MOTU #2 Channel 15
+
#Cue 1 out of your DAW is normalized into Apollo X16 Line Output 15.
−
#MOTU #2 Channel 15 is normalized to the API Echo 1 Module
+
#Apollo X16 Line Output 15 is normalized to the API Echo 1 Module.
−
#Turn ON the Echo 1 module on the API
+
#Turn ON the Echo 1 module on the API.
−
#Press the Ext. In button on the Echo 1 module on the API
+
#Press the TB button on the Echo 1 module on the API. This assigns the Talkback mic to Echo 1.
 +
#Press the Ext. In button on the Echo 1 module on the API. This brings a mult from Apollo X16 Line Output 15 directly into the Echo 1 module.
 
#Turn the Echo 1 pot to about 1 o'clock. This is the overall master volume level for both the API I/O echo trim pots and the cue faders in your DAW.
 
#Turn the Echo 1 pot to about 1 o'clock. This is the overall master volume level for both the API I/O echo trim pots and the cue faders in your DAW.
 
#All Echo 1 sends on all API channels go to the Echo 1 module as well.
 
#All Echo 1 sends on all API channels go to the Echo 1 module as well.
 
#Use these individual Echo 1 trims to control the headphone volume of each LIVE instrument.
 
#Use these individual Echo 1 trims to control the headphone volume of each LIVE instrument.
 +
#'''Make sure to press the PRE button on all the API echo sends on each channel. This allows you to control the headphone level separate from the faders!'''
 
#Use the Cue faders in your DAW to control the volume of your previously recorded material.
 
#Use the Cue faders in your DAW to control the volume of your previously recorded material.
  
 
===='''CUE 2'''====
 
===='''CUE 2'''====
−
#Cue 2 out of your DAW is normalized into MOTU #2 Channel 16
+
#Cue 2 out of your DAW is normalized into Apollo X16 Line Output 16.
−
#MOTU #2 Channel 16 is normalized to the API Echo 2 Module
+
#Apollo X16 Line Output 16 is normalized to the API Echo 2 Module.
−
#Turn ON the Echo 2 module on the API
+
#Turn ON the Echo 2 module on the API.
−
#Press the Ext. In button on the Echo 2 module on the API
+
#Press the TB button on the Echo 2 module on the API. This assigns the Talkback mic to Echo 2.
 +
#Press the Ext. In button on the Echo 2 module on the API. This brings a mult from Apollo X16 Line Output 16 directly into the Echo 2 module
 
#Turn the Echo 2 pot to about 1 o'clock. This is the overall master volume level for both the API I/O echo trim pots and the cue faders in your DAW.
 
#Turn the Echo 2 pot to about 1 o'clock. This is the overall master volume level for both the API I/O echo trim pots and the cue faders in your DAW.
 
#All Echo 2 sends on all API channels go to the Echo 1 module as well.
 
#All Echo 2 sends on all API channels go to the Echo 1 module as well.
 
#Use these individual Echo 2 trims to control the headphone volume of each LIVE instrument.
 
#Use these individual Echo 2 trims to control the headphone volume of each LIVE instrument.
 +
#'''Make sure to press the PRE button on all the API echo sends on each channel. This allows you to control the headphone level separate from the faders!'''
 
#Use the Cue faders in your DAW to control the volume of your previously recorded material.
 
#Use the Cue faders in your DAW to control the volume of your previously recorded material.
−
[[Category:COM 212]]
+
 
 +
===212 Isolation Booth===
 +
The headphone distribution box must be connected in order to get a headphone mix in there.
 +
#Connect the headphone junction box to the 100 ft 1/4 cable.
 +
#Connect the other end of the 1/4 cable to either the CUE 1 or 2 input located on the AMP rack in 212 A.
 +
[[Category:COM 212A]]

Latest revision as of 12:26, 23 October 2023

Headphone Mixes in COM 212A

There are Q 1 & 2 jacks in the 107 Recital Hall. Plug each Little Red Cue Box into either Cue 1 or 2 with the included 1/4" to XLR speaker-level cable. This is the ONLY cable that should be used with the LRCB. Make sure the volume on the LRCB is turned all the way down when not in use.

CUE 1

  1. Cue 1 out of your DAW is normalized into Apollo X16 Line Output 15.
  2. Apollo X16 Line Output 15 is normalized to the API Echo 1 Module.
  3. Turn ON the Echo 1 module on the API.
  4. Press the TB button on the Echo 1 module on the API. This assigns the Talkback mic to Echo 1.
  5. Press the Ext. In button on the Echo 1 module on the API. This brings a mult from Apollo X16 Line Output 15 directly into the Echo 1 module.
  6. Turn the Echo 1 pot to about 1 o'clock. This is the overall master volume level for both the API I/O echo trim pots and the cue faders in your DAW.
  7. All Echo 1 sends on all API channels go to the Echo 1 module as well.
  8. Use these individual Echo 1 trims to control the headphone volume of each LIVE instrument.
  9. Make sure to press the PRE button on all the API echo sends on each channel. This allows you to control the headphone level separate from the faders!
  10. Use the Cue faders in your DAW to control the volume of your previously recorded material.

CUE 2

  1. Cue 2 out of your DAW is normalized into Apollo X16 Line Output 16.
  2. Apollo X16 Line Output 16 is normalized to the API Echo 2 Module.
  3. Turn ON the Echo 2 module on the API.
  4. Press the TB button on the Echo 2 module on the API. This assigns the Talkback mic to Echo 2.
  5. Press the Ext. In button on the Echo 2 module on the API. This brings a mult from Apollo X16 Line Output 16 directly into the Echo 2 module
  6. Turn the Echo 2 pot to about 1 o'clock. This is the overall master volume level for both the API I/O echo trim pots and the cue faders in your DAW.
  7. All Echo 2 sends on all API channels go to the Echo 1 module as well.
  8. Use these individual Echo 2 trims to control the headphone volume of each LIVE instrument.
  9. Make sure to press the PRE button on all the API echo sends on each channel. This allows you to control the headphone level separate from the faders!
  10. Use the Cue faders in your DAW to control the volume of your previously recorded material.

212 Isolation Booth

The headphone distribution box must be connected in order to get a headphone mix in there.

  1. Connect the headphone junction box to the 100 ft 1/4 cable.
  2. Connect the other end of the 1/4 cable to either the CUE 1 or 2 input located on the AMP rack in 212 A.
Retrieved from "http://helpwiki.evergreen.edu/wiki/index.php?title=Headphone_Mixes-COM_212&oldid=44922"

The Evergreen State College